131. Specifications - Arctic Spas

131. Specifications

Specifications
Environmental ratings:
Operating temperature: 32 ̊F (0°C) to 136 ̊F (58 ̊C)
Storage temperature: -13°F (-25°C) to 185°F (85°C)
Humidity: Up to 85% RH, non condensing
IPx5 level of waterproofing
Mechanical:
in.ye
Weight: Up to 97 lbs (44 kg)
Dimensions (W x H x D): 19598″” x 1075″” x 498″” (497 x 273 x 126 mm)
in.yt
Weight: Up to 12 lbs (445 kg)
Dimensions (W x H x D): 958″” x 145″” x 51″” (497 x 368 x 130 mm)
Model Y Series UL/CSA electrical specifications
Input rating: 120/240 V nominal (+5/-10%) (2 lines required with neutral) 48 A Max,
or (inye-3 only): 120 V nominal only (+5/-10%) (single line with neutral) 16 A Max, 60 Hz nominal (+15 / -10 Hz)
Heat.wav rating:
Voltage: 120 or 240 V, 60Hz
Wattage: 4 kW at 240 V, 1 kW at 120 V (Also available: 55 kW at 240 V)
Flow rate: Minimum of 18 GPM (68 LPM) is required
UL 1563 Sixth Ed
UL File: E182156
CSA No 222 – 2181-M89
Model Y Series TUV electrical specifications
Input rating: 230/240 V nominal (+5/-10%) (2-phase system with neutral) 20 A Max per phase, (3-phase system with neutral) 16A Max per phase
or (inye-3 only): 240 V nominal only (+5/-10%) (single-phase system with neutral) 48 A Max, 50 Hz nominal (+15 / -10 Hz)
Heat.wav rating:
Voltage: 240 V, 50Hz
Wattage: 38 kW at 230 V , 28 kW at 230 V
Flow rate: Minimum of 18 GPM (68 LPM) is required
EN/IEC 60335 – 2 – 60/A2: 2008 – EN/IEC 60335 – 1: 2010 EN55014-1
EN55014-2
EN61000-3-2
EN61000-3-3″
“North American Models
Device
Pump 1 (2-spd)
Pump 2 (2-spd)
Pump 3 (2-spd)
Pump 4 (2-spd)
Pump 5 (1-spd)
O3/CP
A1
Blower
CP
O3
Direct out 1
Direct out 2
Voltage
120 or 240 V
Maximum current
15 FLA/60 LRA (inrush)
6 FLA/10 A
10 A (always on)
ye-3* 1
* 1 This model can be converted to a dedicated 120 V model
* 2 Pump #2 can only be installed if Pump #1 is a single-speed pump
* 3 Total of Pump #1-low (or Pumps #2) and O3/ CP cannot exceed 15 FLA
* 7 If CP is used, Pump 3 must be 1-speed
Total of pump 1-low, O3 and Di1 must not exceed 15 FLA Total of P3, CP, and Di2 must not exceed 15 FLA
* 8 If A1 is used, Pump 4 must be 1-speed
Total of O3 and Di1 must not exceed 15 FLA
Total of P3, CP, and Di2 must not exceed 15 FLA Total of P5, and B must not exceed 15 FLA
Total of P4, and A1 must not exceed 20 FLA
European Models
Device
Pump 1 (2-spd)
Pump 2 (2-spd)
Pump 3 (2-spd)
Pump 4 (2-spd)
Pump 5 (1-spd)
O3/CP 230 V
A1 230 V
Blower 230 V
CP 230 V
O3 230 V
Direct out 1
Direct out 2
Voltage
230 V
Maximum current
5 FLA/60 LRA (inrush)
15 FLA/60 LRA (inrush)
6 FLA/10 A
10 A (always on)
ye-3*
* 1 Pump #2 can only be installed if Pump #1 is a single-speed pump
* 2 Total of Pump #1-low (or Pumps #2) and O3/CP cannot exceed 20 FLA