110. Keypad Overview - Arctic Spas

Keypad Overview
In.K300
Compact Full-function Keypad
The quick reference card provides an overview of your spas main functions and the operations accessible form your digital keypad.
The QRC depicts a generic overlay, custom versions may vary.

Off Mode
Pressing Pump 1 for 5 seconds will enable the OFF mode.
This mode allows you to stop all outputs including automatic functions such as filter cycle, heat request and smart winter mode for 30 minutes to perform quick spa maintenance. When off mode is active, the display will toggle between the “off” message, the clock and the water temperature.

The spa light will flash for a few seconds before the end of the 30 minutes ti warm you that the system is about to resume its normal operation. Press Pump 1 or pump 2 (if available) to restart the system before the expiration of the 30 minute delay. When the system resumes its normal operation, the display shows “On” for 3 seconds.

Pump 1
Press Pump 1 Key to turn Pump 1 on at low speed. Press a second time to turn pump to high speed (with a dual- speed pump*). A Built-in timer automatically turns pump off after 20 minutes, unless pump has been manually deactivated first.

The “pump1” indicator lights up when pump 1 is on. With a dual-speed pump, the indicator will flash when pump 1 is on at low speed.

*If singles speed pump: press Pump key to turn pump on. Press pump key again to turn pump off.

Pump 2 Key
Not available on all models

Press Pump 2 Key to turn Pump 2 on at low speed. Press a second time to turn pump to high speed (with a dual-speed pump*). A third time turns pump off. A built-in timer automatically turns pump off after 20 minutes, unless pump has been manually deactivated first.

The “Pump2” indicator lights up when pump 2 is on. With a dual-speed pump, the indicator will flash when pump 2 is on at low speed.

Light key

Press Light key to turn light on. A second press turns light off. A Built-in timer automatically turns lights off after 2 hours, unless it has been manually deactivated first.

The “ light” indicator lights up when lights is on.

Up/Down Keys

Use UP or Down Key to set desired water temperature. The temperature setting will be displayed for 2 seconds to confirm your new selections.

2 pumps spas have a combined Up/Down Key.
Hold the button ti increase the parameter and release the button to stop. Hold the button again to decrease the parameter.

The “Set Pint” icon indicates that the display shows the desired temperature, NOT the current water temperature!

Programming Steps

Program menu
The program menu is accessible by holding down the Light key for 5 seconds. In the program menu the following parameters can be set: clock, the filter or purge cycles, economy mode and temperature units. While you are in the program menu, use the Up or Down key to adjust the parameters and use the Light key to jump to the next parameter.

The changes will be saved after the confirmation of the last parameter only.
If there is no action taken for 10 seconds, the system will exit the program menu without saving any changes.

Setting the clock
Enter the program menu by holding down the Light key for 5 seconds. The display will show the current clock setting with the hour flashing.
Depending on factory settings your system may be set to 24-hour time or 12-hour time.

Setting the hour: Use the Up or Down keys to adjust the hours. Press the Light key to jump to the next parameter, the minutes.
Setting the minutes: Use the Up or Down keys to adjust the minutes. Press the Light key to jump to the next parameter, the filter or purge start time (FS).


Programming the filter/ purge cycles
Depending on system configuration your spa will perform either a filter or a purge cycle. The filter cycle menu consists of the following parameters: the start time (FS), the duration (Fd) and the frequency (FF). The purge cycle menu consists of the following parameters: the start time (FS) and the frequency (FF).

A filter cycle consists of starting all the pumps and blower in high speed for
1 minute (purge step) then, the pump associated with the filter will run in low speed for the remaining duration
of the filter cycle (clean step).
A purge cycle is used when the spa is equipped with a 24 hour circulation pump which provides a continuous clean step. It consists of starting all the pumps and blower in high speed for 1 minute.

Setting filter or purge cycle start time
The display will show FSxx, “xx” representing the starting hour of the cycle. Use the Up or Down key to adjust
the hours. Use the Light
key to jump to the next parameter, filter duration (Fd).

Setting filter cycle duration
(not available on purge systems)
The display will show Fdxx, “xx” representing the dura-
tion in hours of the filter cycle. Use the Up or Down key to adjust the duration. Use the Light key to jump to the next parameter, filter or purge frequency (FF).
0 = no filtration
24 = continuous filtration
It is not recommended to set this to “”0″”.

Setting filter or purge cycle frequency
The display will show FFxx, “xx” representing the number of cycles per day. Use the Up or Down key to adjust the frequency. Use the Light key to jump to the next parameter, economy mode (EP).
The “Filter cycle” indicator lights up when filter is on
and flashes when suspended.

Setting economy mode
This mode allows you to lower the temperature set point of the spa by 20 °F
(11 °C) during a certain period
of the day.
The display will show EPx, “x” representing the state of the programmed economy
(0 = disabled, 1 = enabled). Use the arrow keys to enable or disable economy mode. Use the Light key to jump to the next parameter, economy start time (ES).

Setting economy start time
The display will show ESxx, “xx” representing the hour at which the economy mode will become active. Use the Up or Down key to adjust the hour. Use the Light key to jump to the next parameter, economy duration (Ed).
When the Economy mode is ON, the display will toggle between the “Eco” message, the time, and the water temperature.

Setting economy duration
The display will show
Edxx, “xx” representing
the duration in hour of the economy mode. Use the Up or Down key to adjust the hour. Use the Light key to jump to the next parameter, temperature unit.
24 = continuous economy

Setting temperature unit
Water temperature can be displayed in either Fahrenheit (°F) or Celsius (°C). The dis- play will show F or C.
Use the Up or Down key to change the setting. Use the Light key to save all the parameters.

Smart Winter Mode
Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes.
The “SWM” indicator lights up when freezing is detected and flashes when the purge is active.

Cooldown
After heating the spa water to the desired Set Point, the heater is turned off, but its associated pump (Pump 1 low-speed or CP) remains on for a predetermined period of time to ensure adequate cooling of the heating element, prolonging its useful life.

Water temperature regulation
Every 15 to 90 minutes
the pump will run to ensure accurate water temperature readings as well as avoid heater activation in dry conditions. After verifying pump activation and taking
a water temperature reading if required, the system automatically turns the heater on to reach and maintain water temperature at
Set Point.
Indicator flashes when taking water tempe- rature reading.